Common

How do I stop my mic from making a breath noise?

How do I stop my mic from making a breath noise?

Use a Pop Filter This device is used to slow the air that comes from “plosives.” A plosive is a word that causes a rapid rush of air to hit the microphone. A pop filter softens the sound of a plosive, such as words that start with the letter “P” and “B.”

How do you record a wind instrument?

When recording the flute, an overhead approach with a cardioid mic 6-12″ (pop) and 3-8′ (classical) away, aimed on-axis midway between the mouthpiece and the center of the instrument should yield a nice blend of breathy character and body tone. Again, listen for distracting mechanical and exaggerated breath noises.

READ ALSO:   What are aspects of Jamaican culture?

How do you mic a flute?

HOW TO MIC A FLUTE OR RECORDER

  1. Approx. 5-10 cm away from the instrument, aim the mic halfway between the mouthpiece and the left hand.
  2. Due to its polar character, the flute can also be spot-miked behind and slightly above the head of the player, pointing at the finger holes.

How do you record a wind instrument at home?

Ten Brass Recording and Mixing Tips

  1. For a natural brass sound, use a ribbon microphone.
  2. Don’t close-mic the bell, record the room sound.
  3. Try combining 2 different mic types.
  4. Position the mic below the player’s line of sight.
  5. Point the mic off axis from the bell.
  6. Try pointing the instrument in other directions.

How do you mic a instrument?

To use this technique figure out how wide or tall the instrument is and place a cardioid microphone that same distance away. For example, if you are recording a hammer dulcimer that is 3″ wide, the mic should be placed 3″ away from it. Most if the time this technique will yield a perfectly usable sound.

READ ALSO:   How many POV characters are there in ASoIaF?

What type of microphone is best for flute?

For a jazz flute recording, consider using a condenser microphone. A condenser will generally capture more of the flute’s many overtones, resulting in a bright sound (Clip 1). A dynamic mic gives a less bright and detailed flute sound (Clip 2). This sound may be more suited to a rock or R&B band.

How do you do Eq breathy vocals?

During playback, the higher frequencies are emphasized more, producing that breathy and airy sounding vocal. This can be achieved in other ways, such as compression with an high shelving EQ. Set shelve around 8 khz and boost a few db. Multiband compression will allow you to gain control of high frequencies.

How do I get rid of wind noise on my mic?

1 Use the right microphone (Cardioid) 2 Engage the low-cut filter on the microphone 3 Get as close to the sound source as possible 4 Use a Deadcat Windscreen 5 Remove wind noises from the recording using an EQ or a noise reduction software.

READ ALSO:   How good are M3 grease guns?

How do you blow a gust of wind on a microphone?

Say the word “pick” or “pull” and you unleash a gust of wind toward the mic. Really, hold your hand up two inches from your mouth and say a few P or B words. Can you feel the gust? To your microphone, the puff is like a tsunami sound wave. This burst of air is known as a plosive.

How to stop breathing noise from reaching your microphone?

Finally, using a pop-filter will help to mitigate the little breathing noise that’s left after applying the previous techniques. Placing the microphone correctly alone can prevent the breathing noise and is the most important step in avoiding breaths reaching the microphone.

How to reduce wind noise when recording outside?

How to Reduce Wind Noise when Recording Outside? 1 Use the right microphone (Cardioid) 2 Engage the low-cut filter on the microphone 3 Get as close to the sound source as possible 4 Use a Deadcat Windscreen 5 Remove wind noises from the recording using an EQ or a noise reduction software. More