Which is not a safety precaution when using the lathe?

Don’t do these while using a lathe Do not wear gloves, rings, watches, or loose clothing. Do not place hands on work turning in the lathe. Do not use calipers or gauges on a workpiece while the machine is moving. Do not make heavy cuts on long slender pieces because the work could bend and fly out of the lathe.

What should be the safety precautions for holding the workpiece to the lathe chuck?

Never leave the key in the chuck. Do not let go of the key until it is free of the chuck and secured in its proper holding place. Never attempt to run the chuck on or off the spindle head by engaging the power. Do not stop the rotation of the chuck by reversing the power to the lathe unless tapping holes.

When it comes to safety precautions while working on a lathe machine why one should remove his necktie wristwatch and Jewellery while working?

Remove wrist watches, necklaces, chains and other jewelry. It’s a good idea even to remove your wedding ring since it can catch on rotating work and severely damage your ring finger and hand. Tie back long hair so it can’t get caught in the rotating work.

Why are we required to wear safety goggles when operating lathe machines?

In the manufacturing industry, failure to wear impact-resistant safety glasses while operating industrial machines like lathes is a leading cause of eye injuries. Not only will this protect your eyes from flying debris; it will prevent dust from getting into your eyes.

What are the safety precautions in welding?

KEY POINTS TO REMEMBER

• Be sure the welder is properly installed and grounded.
• Never weld without adequate ventilation.
• Take proper precautions to prevent fires.
• Protect your entire body with fire retardant clothing, shoes, and gloves.
• Wear eye protection at all times.
• Weld only in a firesafe area.

Which of the following are potential safety hazards when operating a lathe?

Metal turning lathe hazards entanglement of clothing in moving parts, such as drive gears, chucks, lead and feed screws and the workpiece. being hit by loose objects on the lathe, such as chuck keys, tools or swarf. entanglement from inappropriate tooling and polishing techniques.

What are the five safety precautions use in machine workshop?

Machine Maintenance

• Do not attempt to oil, clean, adjust or repair any machine while it is running.
• Ensure that all machine guarding is in place and functioning properly.
• Do not leave machines running unattended.
• Do not try to stop the machine with your hands or body.
• Always keep hands, hair, feet, etc.

What are the safety precautions in machine shop?

GENERAL SAFETY TIPS Safety glasses with side shields must be worn at all times. Do not wear loose clothing, loose neckwear or exposed jewelry while operating machinery. Do not work alone. The buddy system is mandatory! • Pull back and secure long hair.

What precautions should be taken while working on a lathe machine?

Safety Precautions while Working on Lathe Machine 1. One should always be sure that all guards are in place before running the machine. 2. Always clamp the work and tool properly with correct size of work and tool holding device.

What are the dangers of Lathe accidents?

A man makes spindles on a lathe. Lathes are exceptionally useful for cutting sheet metal or wood, but if used improperly they can be incredibly dangerous. The Consumer Product Safety Commission says that the most common injuries caused by lathe accidents are broken fingers, cuts to the hands and hot shrapnel in the eyes.

What are the safety precautions to be taken while using the machine?

1. One should always be sure that all guards are in place before running the machine. 2. Always clamp the work and tool properly with correct size of work and tool holding device. 3. Always keep the machine clear of tools. 4. Machine should be stopped before making measurements or adjustments. 5. Wear an apron or a properly fitted shop coat.

What should I look for when buying a lathe?

Educating yourself about the lathe before using it can prevent many accidents. Read the user manual, including all safety procedures, before you start work. Examine the lathe for any loose, damaged or missing parts and be certain that all guards and shields are in place. Lathe cutting tools should also be sharp.